كاميرات بولارويد من نوع سونر عادية وفوق صوتية ٣-a .. كتاب التصوير للهواة

Some of the images are blurry:

The appearance of white areas in the image means that the light reached the film before the image was taken. film tray

Part of the image is missing.

Part of the image may not appear due to film damage by pressing the canister above or below the yellow tab while holding the camera, remember that the film canister must be held from the side

Reasons for blurring an image:

1 - Move the camera while taking a picture. Hold the camera so that it is still until the film is expelled from the camera

2- Take the photo in a dimly lit place. When the red light appears in the viewfinder, remember that you must use a flash or take the time to expose the image.

Imaging through glass: the glass prevents sound waves from reaching the object to be photographed, and thus the focal length is adjusted

For the lens in relation to the glass manually.

- {Do not reset the focal length adjustment switch to the automatic position after adjusting the lenses manually.
Art made of glass, chandeliers, etc.) The light waves may be reflected away from the camera, and if this happens, the image will be blurred

To adjust the lenses manually, put the focal length switch on a manual position: then the distance between the camera and the object to be photographed is estimated, and the focal length adjustment ring is rotated until it reaches this distance in front of the viewfinder on the white indicator, and the yellow dotted line shows the camera's flash distance range (1 - 4) m .

When you have finished using the manual focus length adjustment, remember to return the focus adjustment switch to the automatic position.

Image defects and their treatment:

1- Frequent spots:

If repeated spots or a rod pattern appear on the images, the camera rolls need to be cleaned. It is best to make sure the rollers are clean when loading each film.

2- Cleaning the rollers

Clean in a dimly lit place. Open the film door, rotate the rollers, and clean off any specks of dust with a clean, lint-free cloth dampened with water if necessary, and check the protruding ends of the float roller for dust build-up.

The sound waves collide with the object in the front part of the image and the waves do not reach the object to be photographed:

When the shutter button is pressed, sound waves are transmitted to the central part of the scene, so it must be ensured that there are no obstacles on the way to the subject to be photographed.

6- Taking pictures at an angle towards a soft and flat surface, so the mystical waves are reflected away from the camera, and the lenses must be adjusted manually

7- The object to be photographed is less than 1 meter away from the camera. The movement of the object while taking the picture: You will get the best pictures if the object to be photographed is moving towards you and not towards you

View the image.

Camera defects and their repair:

- If the camera does not expel the cover film:

Press the shutter button, and if the cap does not eject, pull out the film tray and replace it in a dimly lit location. If the cap does not come off, install a new canister. .

B - If the film is not ejected when the shutter button is pressed: 1 - Check the photo counter, as the film canister may be empty. "
2 - Find the flash bar.

3- Pull the film canister in a dimly lit place until you hear the shutter button push forward, then install the canister, and then the film should come out when the door is locked.

If the previous steps did not work in operating the camera, install a new film.

h. If only part of the covering film or of the film is expelled:

-1. Press to release the film canopy until you hear it snap back into place

once again .

2 - Pull the cover or film out

If the camera is not working properly then a new film canister is inserted.

Camera care:

The camera must be handled with care as rough handling may damage sensitive parts. The lens or viewfinder rarely needs cleaning, and if it does, blow off the dust and then clean it gently with a clean, lint-free cloth.

Rolls inside the film door from time to time using a similar cloth dampened with water if necessary

the film :

The Polaroid SX70 film, like all types of films, should be kept in a cool place. It is preferable that the storage be in a place whose temperature is less than 24 C. In the case of long-term storage, the temperature should be less than 18 C. The film can be kept inside its sealed container in a refrigerator. But not in the place where ice is formed (freezer), and before using the film, it must be left for a while until it becomes warm, at room temperature. It usually takes at least an hour

In order to preserve the film in a fresh condition, keep the film inside its realistic and tightly sealed box. The box should not be opened except when the film is used. The camera loaded with the film should be taken care of just as you take care of the film, that is, the camera must be kept in a cool place

the pictures :

When the SX-70 photo is pulled from the camera, it must be handled by the wide white edge. The photo must not be bent, creased, or folded. Do not cut the edges of the photo, as this may damage the photo. The wonderful image resulting from the use of SX-70 film is
One of the best known images in the world of photography, as it is more stable and colorful

Do not fade

Finger prints can be removed easily from photos by blowing

Breathe on the surface of the image and then wipe gently with a paper towel or piece

Clean and soft cloth

Electronic flash:

The camera has been designed to use the flash rod, and through this flash, images exposed to light are produced in the correct way when using the flash at the specified distance, which is about 1-4 meters.

As a result of the existence of a special electronic circuit inside this camera, the electronic flash unit must have suitable electronic properties. camera to get good shooting results