التصوير الفوري ٢-a .. كتاب التصوير للهواة

The electric eye determines the exposure of this background and the subject of photography becomes very light in the image and if the background is more luminous than the main subject of photography. The electric eye determines the exposure according to the bright background, and this causes the subject to appear dark in a large degree in the image. You can correct this error in one of two ways: either by getting close to the subject of the photograph, so that the electric eye can see a little of the background, or adjust the brightness control. Also, sometimes the main subject can be illuminated if it is very dark, by using a flash.

Brightness control:

Leave the setting in its normal setting for most photos, but only if the main subject is too bright or dark for a daytime photo. You can use this standard to adjust the exposure of another image in the same location and with the same light. For a small change, turn it one degree either towards or towards dimming, and for a larger change, turn it by two degrees. If the photos taken with the flash are too bright or too weak, it may be because you are not within the flash distance (flash). Illumination 1.2 - 2 4 metres

movie shadow:

Every photo you take comes out of the camera the same way a film cover came out. And upon expelling the film cover you will notice a black shadow above,
The master will automatically shake this shade to the camera when the film cover comes out, and the shadow will appear in the same way when each image comes out. The purpose of this shade is to protect the images from light during the first moments of development.

Do not tamper with the film shade, as it is a sensitive part of the camera's hardware.

The following precautions can be taken:

surfaces when it is hot. Keep the camera, film, and developed images away from direct sunlight, hot cars, or all hot areas. If the temperature is less than 7°C, keep your image and film as warm as possible, and put each developed image immediately in a warm inner pocket for at least three minutes.

Using the flash in daylight:

The electronic control circuit of this camera is designed to read both daylight and flash light, and then combine them to produce a properly exposed image. It is worth mentioning that the body should be 1.2-2.4 meters away from the camera.

The flash is useful in daylight in the following cases:

1- If the object is in the shadows and the background is bright and lit, then the exposure is in danger of being intense for the background or simple for the body. By using the flash, you can get attractive, sunny and bright images.
than if the body is illuminated side by strong sunlight

The use of the flash reduces or prevents the occurrence of rough and unpleasant shadows.

3- A face lit only by a blue sky and not directly lit by the sun appears in the picture with a blue appearance, and the use of the flash gives a sense of the presence of sunlight

In all cases in which daylight is not available, the shutter remains open for a relatively long exposure period, which results in blurry images. Using a flash reduces exposure time and results in sharp images

Camera care:

Camera Camera: Keep it from dirt, and if an object needs to be cleaned, wipe it with a damp cloth. and to clean the lens, viewfinder, and electric eye. Blow out the dust and then gently wipe it with a soft, lint-free cloth.

Roasting rollers:

Dirt on the rollers and in the door of the film room can cause frequent spots, streaks, and other errors to appear in the images. Check the rollers regularly to ensure they are clean. While cleaning the rollers, it is best to leave an empty film tray to prevent dust in the copier.
And dirt from entering the film room. Turn both wheels with your finger

to rotate freely. Remove dirt with a clean, lint-free cloth, dampened with water if necessary, and check the ends of the rollers, as dirt may collect as well.

The image exit hole has been checked

the film :

Keep the film in a cool place, do not open the film package cover until it is in use, and in particular avoid leaving the film or film camera in a hot and humid place such as a hot room, luggage in a car, or in direct sunlight. tee

the pictures :

The wonderful SX-70 pictures are among the best in the art of photography in terms of their endorsement with fixative and their resistance to color fading. These pictures have an unusually long life, but they must be avoided folding or bending. The completed picture is confined within its frame on a glossy white base that gives it bright light, and there are no waste to get rid of them. Do not cut or trim the edges of the image, as this will damage its appearance

You can easily remove fingerprints from photos by exposing the photo to the vapor produced by breathing and then polishing it with a soft tissue paper or a soft, clean piece of cloth

Camera problems:

Remember that the camera does not work if the group of flashes has five used lamps facing the subject, or if the film canister is empty. If you were able to take a picture, this indicated that the first side was broken, and if the camera did not completely expel the film cover when you closed the film door or pressed the shutter button, then the battery in the film case may be weak. Leave the film shade to return to the camera. Then pull off the film or its cover

And if the camera does not remove the cover of the film itself, then the reason may be a weak battery or its end, press the shutter button

Reasons for the formation of blurry or cloudy images:

Move the camera: Gently press the shutter button and hold the camera still until the image comes out and all camera sounds are silent.

Take the picture in light other than sunlight and without

Flash use:

To obtain the best results when shooting outdoors in light other than sunlight, the camera should be placed on a stable stand or stand

Trio or the use of strobes (flash). Or filming from a distance of not less than 1.2 metres. The camera is designed to produce great images from 1.2 meters or more away

Other errors for images and their treatment:

Often the film canister has deteriorated before or during its packing. Never press on the film canister, as developing chemicals may spill onto the rollers or behind the image

Clean the rollers before taking more pictures and avoid touching chemicals